Black & Decker freewire Instrukcja Obsługi Pobierz pdf (Strona 5)

located on the underside of this MESSENGER HUB. (If you select the same

number and same house code for any additional receivers on this system they will

operate in conjunction with this hub.)

Step 4:

Synchronize your KEY CHAIN REMOTE with your MESSENGER HUB so they

understand how to communicate with each other. (Note: Any additional remote

that is introduced to the system must also be synchronized.)

To synchronize, move the MESSENGER HUB slide switch to LEARN.

While facing

the MESSENGER HUB, press and hold the top “ON” button of the

KEY CHAIN REMOTE for 5 seconds - Figure 2. Be sure to see the green light

flash on the MESSENGER HUB. The flash will indicate that the MESSENGER

HUB is now synchronized with the KEY CHAIN REMOTE.

Now, move the slide switch on the MESSENGER HUB to RUN.

(Note: Door cannot be closed while MESSENGER HUB is in the LEARN mode.)

Step 5:

Turn lamp on first, then plug into the receptacle on the underside of the MESSENGER HUB. Use only

incandescent bulbs up to 500W. Be sure the lamp has been turned on prior to plugging into MESSENGER

HUB.

Press the Local Lamp “ON/OFF” button on the MESSENGER HUB to check that the MESSENGER HUB is

operating correctly. You will hear a “click” when the MESSENGER HUB turns this lamp on and off.

You are now ready to operate the lamp connected to this MESSENGER HUB with the KEY CHAIN REMOTE.

If the MESSENGER HUB is set to UNIT CODE 1, you can use the top ON and OFF buttons on the KEY

CHAIN REMOTE. If the MESSENGER HUB is set to any other HOUSE CODE you will only be able to use

the “HOUSE” (bottom) ON and OFF buttons.

Step by step instructions to set up additional KEY CHAIN REMOTES

A Quick Note Before You Set Up the KEY CHAIN REMOTE:

The KEY CHAIN REMOTE is very convenient for switching on entrance lights while approaching your home. It lets you turn on and off the

Receivers that are set to UNIT CODE 1 (RED) and GROUP 1 on your INDOOR REMOTE and activate all Receivers (same as the House button

on the INDOOR REMOTE).

Step 1:

To synchronize KEY CHAIN REMOTE, set the MESSENGER HUB slide switch to LEARN.

Step 2:

While facing the MESSENGER HUB, press and hold the top ON button on the KEY CHAIN

REMOTE. The green light on the MESSENGER HUB flashes to indicate that the MESSENGER

HUB now recognizes the KEY CHAIN REMOTE.

Step 3:

Set the slide switch on the MESSENGER HUB to RUN.

The KEY CHAIN REMOTE is now ready for use.

The top ON and OFF buttons will activate any Receivers set to UNIT CODE 1 (RED). For convenience we recommend that your entrance

lights be controlled by UNIT CODE 1 (RED).

The middle ON and OFF (GROUP 1) buttons of the KEY CHAIN REMOTE will activate all Receivers programmed on the GROUP 1 setting on

your INDOOR REMOTE.

NOTE: You must have already programmed the GROUP 1 setting on your INDOOR REMOTE for this function of the KEY CHAIN REMOTE to

operate. If you do not have an indoor remote these two buttons cannot be utilized.

The bottom ON and OFF buttons of the KEY CHAIN REMOTE perform the same function as the House button on the INDOOR REMOTE.

Pressing the INDOOR REMOTE HOUSE BUTTON “on” will activate the MESSENGER HUB and ALL the LAMP RECEIVERs / BULB

RECEIVERs set to the system’s HOUSE CODE. Pressing the INDOOR REMOTE HOUSE BUTTON “off” will deactivate the above receivers as

well as all APPLIANCE RECEIVERS.

KEY CHAIN REMOTE BATTERY REPLACEMENT

To change the battery, pry the two halves apart and fit two CR2016 Lithium 3V batteries. Observe the polarity of the batteries. (Writing on back

of battery must face back cover of KEY CHAIN REMOTE.

NOTE: If KEY CHAIN REMOTE is without battery power, for more than 3 hours, the remote’s internal security code must be reset. To do this,

install new batteries, press and hold any button on the remote for 5 seconds, repeat steps 1 through 3 above to synchronize remote with

MESSENGER HUB.

Unit Code Dial

House Code Dial

On/Off Button

Run / Learn Slide Switch

Plug Receptacle

Activates UNIT CODE

1 (RED) only

Activates

GROUP 1 only

Activates all

On or all Off

621530-00FW1000 FREEWIRE MANUAL 12/17/03 9:50 AM Page 5

1 2 3 4 5 6 7

Komentarze do niniejszej Instrukcji

Brak uwag

Black & Decker freewire Instrukcja Obsługi Strona 5

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Zdalne sterowanie Black & Decker freewire